How to Hook up a TV Screen to Work as a Projector in a Church

Using A TV Screen As A Projector In Church

Churches sometimes like to use projectors to get across vital bits of information. It is not uncommon for a church to use projectors to play movies too, and there are many other potential applications for a projector. If you don’t want to have to buy a projector and a projector screen, then you might be looking into other options. How can you hook up a TV screen to use it in the same way as a projector? Well, it actually isn’t too tough to figure out once you dig into the information.

In order to accomplish this, you are going to need to connect the TV to the projector using certain cables. You’ll need to have access to a VGA cable and a home theater audio cable. These will have to run from the projector unit itself all the way to the TV that you are planning on using as a monitor. In many ways, this is going to be simpler than having to install a projector screen.

How to Hook up a TV Screen to Work as a Projector in a Church

Hooking up the Cables

Truly, the most important part of this process is going to be hooking up the cables properly. As mentioned above, you will need to use a VGA cable and a home theater audio cable to hook the projector to the television. There should be a VGA connection in the back of the projector that you can make use of. You will also find a VGA connection on the back of most modern televisions. Connecting the cable should be simple, but you may need to purchase an especially long one if you cannot have the projector located close to the television itself.

The same can be said of the home theater audio cable. You will be running it from the TV all the way back to the projector. The audio connection on the projector is likely going to be located in the back, but it can vary depending on the model of the projector that you are using. Connect your projector and the television to a power source, and you will be good to go.

Getting the television and the projector to work together is actually going to be surprisingly simple. So long as you have the required cables, it will never be an arduous task. You can get things hooked up fast, and it will allow you to accomplish what you set out to do. This is good for when you are planning on using a projector infrequently and don’t want to have to invest in a projector screen. It’s also practical for churches that don’t have room for a projector screen, as it might be easier to set up a TV that you may have laying around for other purposes.

Positioning the Television

The position of the television is very important, as well. You want to make sure that it is placed in an area of the church that will have the right visibility. Generally, you’ll want to place it towards the front in a spot where everyone can see it comfortably. There are situations where churches will want to set up multiple televisions, though. If this is the case, then you will want to factor that into your thought process.

If you are using a multiple television setup, then you should think about symmetry. Positioning televisions on the left and right of the church make sense. You may also wish to have a television positioned near the center to balance things out. For most churches, one television will be just fine to accomplish your goals. It just depends on the size of your church and what it is that you are planning on doing.

Test Things Out

Go ahead and test everything out once you have it all hooked up and positioned. You will want to get an idea of how everything looks and sounds before making use of it in your service. Take a seat out in the pews somewhere and play the projected movie or display the images on the television itself. This will allow you to look at everything, and you can see if it is exactly right.

It may wind up being that you will want to make some adjustments. You can think about moving the television a bit or adjusting certain settings here and there. Just make sure that things come across clearly and that the picture is as crisp as you were hoping. Once you know that it is all going to work out fine, you will be able to use it in your service with full confidence.


Taking the time to connect your projector unit to your TV is going to work out very well. This will allow you to use a simple modern HDMI television to display your projector images. This has many different applications and you can use it to great effect. Connecting the necessary cables is very simple and it does not take a lot of fiddling with the unit to get things looking really nice.

Keep in mind that the quality of your experience will partially depend on the type of projector that you purchased, too. You will want to try to buy a projector for your church that has a good resolution and a high contrast ratio. This allows for better colors and a crisper image overall. The light resolution is also something to consider, so be sure to look at the specifications of any projector that you are thinking about buying.

Once you have this set up right, you’ll be able to play movies or project certain images or scriptures on the screen during your sermon. Whatever your ideas for the projector are, using the modern televisions in place of projector screens will work out well. It’s not hard to accomplish, and it should wind up being cost-effective for your church, too. This will be useful for any of your main church programs and can also be beneficial to youth programs. Keep the information in mind, and you should not have any trouble accomplishing what you have set out to do.